LiveZilla Live Chat Software
  • pic1
  • pic2
  • pic3
  • pic4
sale1
T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders-T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders Loading image. Please wait
This is the caption of image number one.
T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders-T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders
T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders-T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders
T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders-T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders
T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders-T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders
T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders-T-Rex Buell XB12X  XB12S  XB12R and XB9SX  XB9R Frame Sliders
This is the caption of image number one.
This is the caption of image number two
This is the caption of image number three
This is the caption of image number four
This is the caption of image number five
This is the caption of image number six
This is the caption of image number seven
This is the caption of image number eight
This is the caption of image number nine
This is the caption of image number ten
#N141-8 T-Rex Buell XB12X XB12S XB12R and XB9SX XB9R Frame Sliders
  • Condition = New
  • Special feature = The pucks are solid and not hollow, made to withstand a greater impact. The brackets are designed NOT to rotate in a low side.
  • Material  = UHMW-PE (ultra high molecular weight polyethylene) Brackets are made of aircraft grade aluminum  6061-T6 bracket finished in black anodizing for durability.
  • Slider dimensions = Approx. 2" and 3" in length and 2" in diameter.
  • NO CUT or plastic fairings modification required.
  • Fit Models = BUELL
  • 08 and on XB12X , 08 and on XB12S , 08 and on XB12R
  • 08 and on XB9SX , 08 and on XB9R
  • Buell A pair of "No-Rotation" frame sliders / plastic body protectors (one LHS and one RHS) that fits the above model. The sliders feature a new design of a complete solid puck without a hollowed-out center. This increases the strength and contact surface to about 30%. The bracket is bolted to the engine mount and the aluminum spacer is bolted to the bracket. The slider puck is then screwed on to the spacer. Since this spacer is made of solid billet aluminum there is no need for re-tightening the engine bolt in the long run where you have to do so with plastic slider as the plastic would gradually give in and therefore making the bolt loose. The slider pucks are made of UHMW-PE (ultra high molecular weight polyethylene), a tough plastic with good strength, wear resistance and dimensional stability. It is more dimensionally stable than Nylon and used in many industrial ball bearing and friction reducing applications. Compared to Delrin, it is softer but tougher. Delrin is harder but more brittle. It is an ideal material for slider since it can absorb more impact force onto itself and therefore reduce the impact on the frame and engine. The slider pucks can be inexpensively replaced in case of a low side. We use highest grade commercially available 12.9 bolts (177,000 psi in tensile strength) wherever possible. The bracket is machined from solid steel plate and attached to the frame at multiple locations to avoid rotation that can damage the plastic fairings (see more explanation below). Rest assured that you are getting the best material commercially available. The frame sliders you will receive will most likely be the one pictured above. However, due to constant improvement, the frame sliders can sometimes vary slightly from that in the picture.
Price:$94.95
Qty: